Renesas User System Interface Board HS7047ECH61H Instrukcja Użytkownika Strona 230
- Strona / 243
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
144
Table 6.1 Error Messages at Initiation
Error Message Description and Solution
There is no configuration file. The configuration file that is required to initiate the emulator
cannot be found. Exit and re-install the High-performance
Embedded Workshop. Then re-connect the user system
interface cable, turn on the power of the emulator, and re-
initiate the High-performance Embedded Workshop. If the
problem is not solved, contact us and describe the error
occurrence in detail.
The contents of the configuration file
are incorrect.
The configuration file that is required to initiate the emulator
is invalid. Exit and re-install the High-performance Embedded
Workshop. Then re-connect the user system interface cable,
turn on the power of the emulator, and re-initiate the High-
performance Embedded Workshop. If the problem is not
solved, contact us and describe the error occurrence in
detail.
Main Board not Support (XX XX XX)
Emulator is switched off or not
connected
The emulator power is not turned on, or the user system
interface cable is not connected. Exit the High-performance
Embedded Workshop, re-connect the user system interface
cable, turn on the power of the emulator, and re-initiate the
High-performance Embedded Workshop. If the problem is
not solved, contact us and describe the error occurrence in
detail.
Emulation Board not Support
(XX XX XX)
Emulator is switched off or not
connected
The emulator power is not turned on, or the user system
interface cable is not connected. Exit the High-performance
Embedded Workshop, re-connect the user system interface
cable, turn on the power of the emulator, and re-initiate the
High-performance Embedded Workshop. If the problem is
not solved, contact us and describe the error occurrence in
detail.
EVA chip Board not Support
(XX XX XX)
Emulator is switched off or not
connected
The emulator power is not turned on, or the user system
interface cable is not connected. Exit the High-performance
Embedded Workshop, re-connect the user system interface
cable, turn on the power of the emulator, and re-initiate the
High-performance Embedded Workshop. If the problem is
not solved, contact us and describe the error occurrence in
detail.
Can’t initialize G/A registers An error occurred during the initialization of the emulator. Exit
the High-performance Embedded Workshop, re-connect the
user system interface cable, turn on the power of the
emulator, and re-initiate the High-performance Embedded
Workshop. If the problem is not solved, contact us and
describe the error occurrence in detail.
There is no effective clock source A valid clock source cannot be found. Connect a valid clock
source.
This mode can not specify The state of mode pins for the target board is incorrect.
Initiation is only possible in mode 4. Set the mode pins
correctly.
- SH7046 E6000H Emulator 1
- IMPORTANT INFORMATION 5
- LIMITED WARRANTY 6
- DISCLAIMER 6
- SAFETY PAGE 8
- Warnings on Emulator Usage 10
- CAUTION 11
- About This Manual 14
- Contents 15
- Hardware Part 19
- LAN adapter 22
- (option) 22
- USB adapter 22
- 1.3 System Configuration 27
- Enlarged 34
- Signal Name Delay Time (ns) 46
- _RES 15.0 46
- 0.65 × 19 = 12.35 ± 50
- 0.65 ± 0.05 50
- 0.50 × 24 = 12.00 ± 0.05 53
- 0.50 ± 0.05 53
- × 12 mm) 55
- 0.5 × 35 = 17.5 59
- Evaluation chip board 60
- Connector: WD-200P-VF85-N 60
- PD24/D24/_DREQ0/_UBCTRG 65
- PA2/SCK0/_DREQ0/IRQ0/ 68
- A2/PCIO/ACK2/ 68
- PA5/SCK1/_DREQ1/_IRQ1/ 68
- A5/_POE6/ACK3/ 68
- Message Description 81
- Debugger Part 85
- Section 1 Overview 87
- 2.2 Connecting the Emulator 99
- 2.4 Ending the Emulator 100
- Section 3 Debugging 101
- [Pin Select Registers] page 104
- 3.2 Downloading a Program 108
- , e.g., #PC+0x100 112
- 3.6 Looking at Variables 121
- 3.7 Using the Event Points 123
- 3.9 Analyzing Performance 152
- 3.10 Profiling Function 163
- 3.11 [Profile-Chart] Window 167
- Section 4 Tutorial 169
- 4.5 Setting Registers 174
- 4.6 Executing the Program 175
- 4.7 Reviewing Breakpoints 178
- 4.8 Referring to Symbols 179
- 4.9 Viewing Memory 180
- 4.10 Watching Variables 181
- 4.15 Break Function 190
- 4.16 Trace Functions 198
- 4.17 Stack Trace Function 210
- 4.19 Monitor Function 215
- 4.20 What Next? 217
- 5.1 Supported Hardware 219
- 5.2 Debugging Platform 219
- 5.4 Executing Your Program 221
- 5.5 Event Functions 221
- 5.6 Trace Functions 223
- 5.7 Monitor Function 224
- 5.9 Profiling Function 225
- 5.10 Input Format 225
- 5.11 Tutorial Program 226
- 5.12 Memory Map 226
- SB: Short block 227
- LB: Large block 227
- Section 6 Error Messages 229
- Appendix A Menus 233
- Table A.1 GUI Menus (cont) 235
- Appendix B Command Lines 237
- User's Manual 241
- RENESAS SALES OFFICES 242
- User’s Manual 243
Powiązane produkty i podręczniki dla Networking Renesas User System Interface Board HS7047ECH61H
(4 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji