Renesas Renasas Single-Chip Microcomputer SH7086 Instrukcja Użytkownika

REG10J0125-0100 Renesas Starter Kit for SH7211 User's Manual RENESAS SINGLE-CHIP MICROCOMPUTER SuperHTM RISC engine

Description Function Fit for RS232 Remove for RS232 Fit for E8a Remove for E8a TxD1 Programming Serial Port R47 R21, R56 R21 R47,R56 RxD1 P

6.6. Option Links Table 6-5 below describes the function of the option links contained on this CPU board. The default configuration is indicated by B

Table 6-6 below describes the function of the option links associated with Power configuration. The default configuration is indicated by BOLD text.

Table 6-8 below describes the function of the option links associated with Pin function configuration. The default configuration is indicated by BOLD

Option Link Settings Reference Function Fitted Alternative ( Removed ) Related To R111 Pin function select Connects PIN 120 to DREQ0 on JA6. D

6.7.Oscillator Sources A crystal oscillator is fitted on the CPU board and used to supply the main clock input to the Renesas microcontroller. Table

Chapter 7.Modes The CPU board can be configured in User mode and Boot mode. User mode may be used to run and debug user code, while Boot mode may onl

Chapter 8. Programming Methods The board is intended for use with HEW and the supplied E10A debugger only. Please refer to SH7211 Group Hardware Man

Chapter 9. Headers 9.1. Microcontroller Headers Table 9-1 to show theTable 9-4 microcontroller pin headers and their corresponding microcontrolle

J2 Pin Circuit Net Name Device Pin Pin Circuit Net Name Device Pin 1 D0 37 19 GND 55 2 D1 38 20 D13 56 3 D2 39 21 D14 57 4 D3 40 22 D15 5

Table of Contents Chapter 1. Preface...

J3 Pin Circuit Net Name Device Pin Pin Circuit Net Name Device Pin 1 VCC 73 19 M1_TRISTn 91 2 GND 74 20 IRQ0 92 3 LED0_M2Vn 75 21 AVSS 93

J4 Pin Circuit Net Name Device Pin Pin Circuit Net Name Device Pin 1 RXD2_TCLKD 109 19 A4 127 2 TXD2_TCLKC 110 20 A5 128 3 DLCDE 111 21 A6 1

9.2. Application Headers Table 9-5 to Table 9-9 below show the standard application header connections. * marks pins where a link to the microcontrol

JA2 Pin Header Name CPU board Signal Name Device Pin Pin Header Name CPU board Signal Name Device Pin 1 RESn RESn 22 14 Un M1_Un 120* 2 EXT

JA3 Pin Header Name CPU board Signal Name Device Pin Pin Header Name CPU board Signal Name Device Pin 1 Address Bus A0 121 26 Read/Write Cont

JA5 Pin Header Name CPU board Signal Name Device Pin Pin Header Name CPU board Signal Name Device Pin 1 AD4 AN4 101 13 TIOC0A TIOC0B 6 2 AD

Chapter 10. Code Development 10.1. Overview Note: For all code debugging using Renesas software tools, the CPU board must either be connected to a P

10.4.Memory Map The memory map shown in this section visually describes the locations of the each memory areas when operating the RSK in the default

Chapter 11. Component Placement Figure 11-1: Component Placement (Top Layer)26

Chapter 12. Additional Information For details on how to use High-performance Embedded Workshop (HEW), refer to the HEW manual available on the CD o

Chapter 1. Preface Cautions This document may be, wholly or partially, subject to change without notice. All rights reserved. No one is permitted t

Renesas Starter Kit for SH7211 User's Manual Publication Date Rev.1.00 17.Jan.2008 Published by: Renesas Techn

Renesas Starter Kit for SH7211 User's Manual Renesas Technology Europe Ltd.Dukes Meadow, Millboard Road, Bo

Chapter 2. Purpose This RSK is an evaluation tool for Renesas microcontrollers. Features include: • Renesas Microcontroller Programming. • User C

Chapter 3. Power Supply 3.1. Requirements This CPU board operates from a 5V power supply. A diode provides reverse polarity protection only if a cur

Chapter 4. Board Layout 4.1. Component Layout The following diagram shows top layer component layout of the board. JA3JA5 JA1JA6 JA2J4J2J1User LEDs

4.2. Board Dimensions The following diagram gives the board dimensions and connector positions. All through hole connectors are on a common 0.1” grid

Chapter 5. Block Diagram Figure 5-1 shows the CPU board components and their connectivity. Figure 5-1: Block Diagram Figure -5-2 shows the conne

Chapter 6. User Circuitry 6.1. Switches There are four switches located on the CPU board. The function of each switch and its connection are shown i