Renesas H8S/2168 Instrukcja Użytkownika Strona 1

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Maszyna do redukcji hałasu Renesas H8S/2168. ATCA-5000/5100 Hardware Reference Instrukcja obsługi

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj

Podsumowanie treści

Strona 1 - PROMENTUM™

www.radisys.comPROMENTUM™ SHELF PERIPHERAL MODULEHARDWARE REFERENCE007-02656-0000 • December 2006ATCA-5000ATCA-5100

Strona 2 - Release Date Description

Product Description110Electrical componentsFigure 2. Block diagram of electrical components +12 V from hot-swap control +12 V+2.5 V+3.3 VIPMB-0 Displa

Strona 3 - TABLE OF CONTENTS

Face plate111Face plateFigure 3. Face plateEvent input connectorHot-swap LEDPIMOOS LEDPWR LEDApplication LEDTelco alarm connectorSerial port

Strona 4

Product Description112

Strona 5 - Additional resources

13THEORY OF OPERATION2This chapter describes the main components of the SPM.IPMC subsystemThe Intelligent Platform Management Controller (IPMC) subsys

Strona 6

Theory of Operation214Hot-swap mechanismA hot swap switch on the bottom of the SPM is activated by the lower ejector latch. It can be used to request

Strona 7 - PRODUCT DESCRIPTION

Telco alarm interface215Telco alarm interfaceA telco alarm interface, as specified in the PICMG 3.0 Revision 2.0 AdvancedTCA Base Specification, is pr

Strona 8

Theory of Operation216The following diagram shows the suggested external connection to external equipment.Figure 4. Relay output connection—External c

Strona 9 - Specifications

Shelf interfaces217Figure 5. Reset input connection—External connection to external equipmentShelf interfacesThe following shelf I/Os are monitored by

Strona 10 - Electrical components

Theory of Operation218IPMB interfaceThe SPM communicates with the rest of the system components through an Intelligent Platform Management Bus (IPMB-0

Strona 11 - Face plate

RTM function for front module219When not ‘active,’ the Renesas H8S/2168 microcontroller in the IPMC subsystem will configure the SPM external interfac

Strona 12 - Product Description

Release historyRelease Date Description-0000 December 2006 Initial releaseCopyright © 2006 by RadiSys Corporation. All rights reserved. RadiSys is a

Strona 13 - NV memory

Theory of Operation220On the ATCA-5000, the following signals to Jn4 are routed as 100-Ohm differential pairs from the Zone 3 connector to the PIM Jn4

Strona 14 - Event inputs

Power22110/100/1000 Ethernet interfacesTwo 10/100/1000 Ethernet connections are routed from the 3x32 DIN shelf connector to the daughter card connecto

Strona 16 - Theory of Operation

23CONNECTORS3Face-plate connectorsTelco alarm interface connectorThe Telco Alarm Interface connector is a 15-pin male D-shell (DA-15P) connector with

Strona 17 - Shelf interfaces

Connectors324The mating terminal block accepts 28 through 20 AWG solid or stranded wires, stripped to expose an 8-mm length of conductor. The followin

Strona 18 - Redundancy

Interior connectors325Interior connectorsFigure 9. Interior connectors3x32 DINconnector1x3 powerconnectorPIM sitePIM Jn0connectorPIM Jn4connectorDaugh

Strona 19 - RTM function for front module

Connectors326Zone 3 connector (ATCA-5000 only)Connections between the ATCA-5000 and the ATCA-2100 occur across a female DIN 41612-type connector, loca

Strona 20 - Shelf Manager interface

Shelf ground headers3273x32 shelf connectorConnections between the SPM and the system occur across a female DIN 41612 type connector. It is located ab

Strona 21

Connectors328PIM Jn0 connectorJn0 matches VITA 36 (custom assignment).Table 10. Jn0 PIM connector pin assignmentsPin Signal Pin Signal1 not connected

Strona 22

PIM interfaces329PIM Jn4 connectorJn4 matches VITA 36 (custom assignment) Table 11. Jn4 PIM connector pin assignmentsPin Signal Pin Signal1VITA[1] 2VI

Strona 23 - Face-plate connectors

3TABLE OF CONTENTSPreface ... 5Electro

Strona 26 - Connectors

5PREFACEThis manual describes the ATCA-5000 and ATCA-5100 shelf peripheral modules (SPMs) and assists engineers, technicians, and developers in using

Strona 28 - PIM Jn0 connector

7PRODUCT DESCRIPTION1The ATCA-5000 and ATCA-5100 shelf peripheral modules (SPMs) provide an interface for ATCA shelf management to various shelf perip

Strona 29 - PIM Jn4 connector

Product Description18Figure 1. ConnectionsThe SPM provides a PMC I/O Module (PIM) interface that the SCM can use.A connector is provided that is desig

Strona 30

Features19Features IPMC subsystem based on a Renesas H8S/2168 microcontroller that provides an interface to the ATCA IPMB-0 bus Event inputs—four op

Komentarze do niniejszej Instrukcji

Brak uwag