Renesas Emulator System E8 Informacje Techniczne

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C

2

3 Section 2 Connecting the Emulator with the User System Before connecting an E8/E8a emulator (hereafter referred to as emulator) with the user sys

4 Notes: 1. The pin number assignments of the 14-pin connector differ from those of the E10A-USB emulator; however, the physical location is the sa

5 Section 3 Pin Assignments of the E8/E8a Connector Figure 3.1 shows the pin assignments of the connector. Pin 1 markPin 1 markTop viewConnectorPin

6

7 Section 4 Example of Emulator Connection Figure 4.1 shows an example of emulator connection to the MCU. *: Open-collector bufferConnector14 pins

8 Notes: 1. P33 to P35 pins are used by the emulator. Pull up and connect the emulator and MCU pins. P33 to P354.7 kΩUser system connectorPins 1,

9 4. Connect Vss and Vcc with the Vss and Vcc of the MCU, respectively (within the guaranteed range of the microcomputer). When the power-supply mod

10 VccRES#811151322 Ω100 kΩx 33.3 V22 Ω22 Ω22 ΩP33Emulator control circuitUser system connectorP34P3574LVC125A74LVC125A74LVC125A722 ΩP9574LVC125A (3.

11 VccRES#811151322 Ω100 kΩx 33.3 V22 Ω22 Ω22 ΩP33Emulator control circuitUser system connectorP34P3574LVC125B74LVC125B74LVC125B722 ΩP9510 kΩ10 kΩ2CS

Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang

12

13 Section 5 Differences between the MCUs (H8/38024F and H8/38004F) and the Emulator This section describes the differences between the emulator an

14 To keep the [Emulator Setting] dialog box closed next time the emulator is started, check "Do not show this dialog box again." at the bo

15 • Program Flash This mode is used when the emulator is used for programming the flash memory. Debugging the program is disabled. To download the

16 Figure 5.3 [ID Code] Dialog Box Note: For the E8a emulator, the initial value is H’0E8a. 4. When the emulator system is initiated, it initial

17 7. System Control Register In the emulator, the internal I/O registers can be accessed from the [IO] window. However, be careful when accessing

18 Table 5.2 Program Area for the E8/E8a Emulator MCU Name Program Area H8/38024F H8/38004F Flash memory: H’7000 to H’7FFF Internal RAM: H’F780 to

19 16. Items Set in the [Configuration] Dialog Box The emulator operation conditions are set in the [Configuration] dialog box. Figure 5.4 [Config

20 Items that can be displayed in this dialog box are listed below. [Device] combo box Displays the MCU name. [Emulation mode] combo box Selects

21 If there is no problem with the state that the program in the flash memory has been replaced as the PC break code, the position where the PC bre

E8/E8a EmulatorAdditional Document for User’s ManualNotes on Connecting the H8/38024F and H8/38004FUser’s Manual Rev.4.00 2007.07Renesas Microcomput

22 [Short break] group box Enables or disables memory access during user program execution. Disable: Disables memory access during user program ex

E8/E8a EmulatorAdditional Document for User's ManualNotes on Connecting the H8/38024F and H8/38004FPublication Date

Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japanhttp://www.renesas.comRefer to

1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 JapanE8/E8a EmulatorREJ10B0212-0400Additional Document for User’s ManualNotes on Conn

1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use.

iContents Section 1 Inside the E8/E8a Emulator User’s Manual...1 Section 2 Connecting the Emulator with the

ii

1 Section 1 Inside the E8/E8a Emulator User’s Manual The E8 or E8a emulator (hereafter referred to as E8/E8a in this document) manual consists of t