Renesas User System Interface Cable HS36049ECH61H Instrukcja Użytkownika Strona 1

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C

IV SAFETY PAGE READ FIRST • READ this user's manual before using this emulator product. • KEEP the user's manual handy for future referenc

V WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emu

VI Warnings on Emulator Usage Be sure to read and understand the warnings below before using this emulator. Note that these are the main warnings, n

i Preface Thank you for purchasing this user system interface cable (HS36049ECH61H) for the Renesas’ original microcomputer H8/36049 group. The HS360

ii Contents Section 1 Configuration...1 Section 2 Connection Pr

1 Section 1 Configuration CAUTION Use an IC149-080-017-B5 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the FP-80A package

2 Table 1 lists the HS36049ECH61H components. Please make sure you have all of these components when unpacking. Table 1 HS36049ECH61H Components No

3 Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station (without Channel 3 of Serial Communication Interf

4 Emulator stationCable body connectorUser system interface cableCTS screws (M3 x 6 mm)E6000 Figure 2 Connecting User System Interface Cable to Emu

5 2.2 Connecting User System Interface Cable to Expansion I/O Board (with Channel 3 of Serial Communication Interface for H8/36049 Group) WARNING

Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang

6 Cable body connectorUser system interface cableCTS screws (M3 x 6 mm)Expansion I/O boardUSER INTERFACE CABLE6000 EMULATOE6000 Figure 3 Connecting

7 2.3 Connecting User System Interface Cable to User System WARNING Always switch OFF the user system and the emulator product before the USE

8 2.3.3 Inserting Cable Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an FP-80A package on the us

9 Fasten the user system interface cable head to the IC socket for an FP-80A package on the user system with the four screws (M2 x 12 mm; with four f

10 2.3.5 Fastening Cable Body Connect the cable body to the cable head. Cable bodyCable headRemove jigUser systemPush two remove jigs.Removing Figure

11 2.4 Recommended Dimensions for User System Mount Pad Figure 6 shows the recommended dimensions for the mount pad (footprint) for the user system

12 2.5 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 7. Unit

13 2.6 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable

14 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver

15 MCUPin 1IC socket (IC149-080-017-B5manufactured by YAMAICHI ELECTRONICS Co., Ltd.)User systemScrews (M2 x 8 mm)with flat washersSocket cover Figur

H8/36049 Group FP-80AUser System Interface CableUser’s ManualUser’s Manual Rev.3.00 2005.10Renesas Microcomputer Development Environment SystemHS360

16 Section 4 Verifying Operation 1. Turn on the emulator according to the procedures described in the H8/3664 E6000 Emulator User’s Manual (HS3664

17 Figure 10 shows the system clock oscillator on the user system interface cable and the subclock input specifications. To E6000 emulatorSystem cloc

18 Section 5 Notice 1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the ca

19 6. The P1 short connector is used for testing. Do not remove the inserted jumper pin. P113 Figure 12 P1 Short Connector

H8/36049 Group FP-80A User System Interface Cable User's ManualPublication Date: Rev.1.00, May 23, 2003 Rev.3

Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japanhttp://www.renesas.comRefer to

1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 JapanH8/36049 Group FP-80AUser System Interface CableREJ10J1150-0300User’s Manual

1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the c

I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this emulator product. • KEEP the user's manual handy for future

II LIMITED WARRANTY Renesas warrants its emulator products to be manufactured in accordance with published specifications and free from d

III State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages